Flysky FS-X6B 6CH Receiver for FS-i10 FS-i8 FS-i6 FS-i6s FS-i6x FS-i4 FS-i4x Transmitter


Flysky - Outputs channels 1 6 PWM. Ppm signal port: Outputs standard PPM signal. Ibus signal port: outputs iBus signal, up to 18 channels. Press and hold the receiver code key, connect the power of the 1S to 4S,  the light flashing on the receiver indicates that the receiver enters the state of the code. Caution do not connect the receiver with excessive current.

. The receiver's indicator light stops fast flashing  turns to always bright. X6b supports 3 kinds of signal output, 6 channel PWM output, 8 channel PPM output and 18 channel i-BUS output. Pairs of codes are successful, the transmitter automatically withdraws the code interface. Specification channels:6 pwm, 8 ppm, 18 iBUS  RF range:2.

Flysky FS-X6B 6CH Receiver for FS-i10 FS-i8 FS-i6 FS-i6s FS-i6x FS-i4 FS-i4x Transmitter - 408 to 2. 475 ghz  band width:500 khz  Power input:4. 0 to 8. 4v ports pwm signal port:GND, VCC. Check whether the transmitter  receiver work properly, if there is an exception please stop the operation immediately. Package includefs x6b receiver receiver compatible with fs-i10, FS-i8, fs-i6s, FS-i4, fs-i6x, fs-i6, FS-i4x ect.

Fs series RC transmitter.

More information about Flysky

Flysky A8S 8CH Receiver 2.4Ghz PPM i-BUS S-BUS for Flysky i4 i6 i6S i6X TM10 TM8 Transmitter Racing Quadcopter


Flysky - Specification: connectors these ports are for connecting the receiver to various models and flight controllers PPM signal port: Outputs standard PPM signal. It will make your vehicle more sensitive obedient and better finish it, "a UAV mission. ". 3. On the transmitter, manually exit the binding menu. Binding 1.

For information on putting the transmitter into bind mode please refer to the transmitters user manual. Led turns off for 1 second then flashes twice: i-BUS output mode active. If binding is successful the receiver's LED will begin to flash slower. Package include: 1* fs a8s receiver receiver compatible with fs-i4, fs-gt2e, fs-gt2g, FS-i10, fs-i6s, fs-i6x, fs-i6, FS-GT2F.

Flysky A8S 8CH Receiver 2.4Ghz PPM i-BUS S-BUS for Flysky i4 i6 i6S i6X TM10 TM8 Transmitter Racing Quadcopter - Fs series RC transmitter. It uses the afhds 2a automatic Frequency Hopping Digital System protocol prevent signal interference. The a8s supports 8-channel pwm signal output, a standard PPM signal outputs, 18 channels of I-BUS signal and a voltage detection interface. Three seconds fast response, small size, powerful, easy to carry.

Fs-a8s is a two-way receiver designed specifically for multi-axis aircraft, rich interface, has a powerful anti-jamming capability, good compatibility. Change i-BUS/S. Bus mode when turned on and bound, the transmitter and receiver can change output mode to i-BUS and S.

More information about Flysky


Similar products



usmile FS82 2.4G Micro receiver for Flysky Micro Carbon Fiber Quad Frame FPV racing drone Support for AFHDS 2A IBUS PPM FS-I4,FS-I6,FS-I6X,FS-I10,FS-GT2E, FS-GT2G,FS-GT2F, Turnigy Evolution


Usmile - Range:about 200m. Suit for brushed Quadcopter and other small size quads. It is compact and easy to install. Binding procedure:hold down the bind button before powering the receiver, blue light goes off then flashes slowly indicates a sucessful binding, re-connect the receiver and transmitter, release the button to enter bind mode, hit bind button on the transmitter, the blue indicator light flashes quickly, select protocol AFHDS 2A, then turn on the transmitter, the blue light should be steady now.

It will make your vehicle more sensitive obedient and better finish it, "a UAV mission. ". Small and lightweight, fs-gt2g, fs-i6, fs-gt2F, fs-i10, Compatible with FS-I4, fs-gt2e, fs-i6x, Turnigy Evolution. Afhds 2a protocol, output: PPM/IBUS. Channels: ppm 8ch / ibus 10CHFrequency range: 2. 408-2. 475ghz 2. 4ghz system: afhds 2awork mode: ibus or PPMIBUS connector: 1.

usmile FS82 2.4G Micro receiver for Flysky Micro Carbon Fiber Quad Frame FPV racing drone Support for AFHDS 2A IBUS PPM FS-I4,FS-I6,FS-I6X,FS-I10,FS-GT2E, FS-GT2G,FS-GT2F, Turnigy Evolution - 0 sh 3pin plugppm connector: solder padfailsafe function: support only IBUS ModeTransfer method: FHSS Antenna length: 30mm Range: about 200m Working current: 40mASize: 20*13*4. 5mm weight: 1. 2g compatible transmitter: compatible with fs-i4, fs-i10, fs-gt2e, fs-gt2f, fs-i6s, FS-i6X, FS-i6, FS-GT2G, Turnigy EvolutionOther parts you might be interested: 5.

More information about Usmile


Similar products



FPVKing Flysky FS-X6B Receiver 6 CH 2.4G i-Bus PPM PWM Receiver for AFHDS i10 i6s i6 i6x i4x Transmitter with 250mm Lipo Battery Strap


FPVKing - It will make your vehicle more sensitive obedient and better finish it, "a UAV mission. ". Small and lightweight, compatible with fs-i4, fs-gt2F, fs-i6, fs-gt2g, fs-gt2e, fs-i10, fs-i6x, Turnigy Evolution. Afhds 2a protocol, output: PPM/IBUS. The fs-x6b receiver is a 6 channel two-way receiver designed for multi-rotor aircraft.

It's compact, easy to install and boasts a rich easy to use interface. It supports 6 channel pwm output, standard PPM output and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface. Compitable transmitter: all afhds 2a transmitters, FS-i6X, FS-i10, fs-i6, FS-i6S, fs-i4, FS-i8, FS-i4X.

FPVKing Flysky FS-X6B Receiver 6 CH 2.4G i-Bus PPM PWM Receiver for AFHDS i10 i6s i6 i6x i4x Transmitter with 250mm Lipo Battery Strap - The fs-x6b receiver is a 6 channel two-way receiver designed for multi-rotor aircraft. It's compact, easy to install and boasts a rich easy to use interface. It supports 6 channel pwm output, standard PPM output and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface. Easy to bind with transmitter: https://www.

Youtube. Com/watch?v=5yZG631iXwQ. Superior noise reduction techniques:It uses the AFHDS 2AAutomatic Frequency Hopping Digital System protocol and dual omnidirectional antenna.

More information about FPVKing


Similar products



Tattu 4S 1300mAh LiPo Battery 75C 14.8V Pack with XT60 Plug for RC Boat Heli Airplane UAV Drone FPV Skylark Emax Nighthawk 250


Tattu TA-75C-1300-4S1P - 2. For any questions, pls feel free to contact us through "Your Orders" tab of your Amazon account, we will respond within one business day. It is compact and easy to install. Receiver compatible with fs-i4, fs-gt2g, fs-gt2e, FS-i10, fs-i6s, fs-i6x, fs-i6, FS-GT2F. Fs series RC transmitter. It uses the afhds 2a automatic Frequency Hopping Digital System protocol prevent signal interference.

The a8s supports 8-channel pwm signal output, a standard PPM signal outputs, 18 channels of I-BUS signal and a voltage detection interface. Three seconds fast response, powerful, small size, easy to carry. Fs-a8s is a two-way receiver designed specifically for multi-axis aircraft, has a powerful anti-jamming capability, rich interface, good compatibility.

Tattu 4S 1300mAh LiPo Battery 75C 14.8V Pack with XT60 Plug for RC Boat Heli Airplane UAV Drone FPV Skylark Emax Nighthawk 250 - Suit for brushed Quadcopter and other small size quads. Tattu professional lipo Battery; Superior Japan and Korea Lithium Polymer raw materials. Quickly recharged, long cycle life 150 times minimum, up to 200Wh/kg energy density. Parameter: weight, 155g; dimensionl*w*h, 72*36*29. 4mm; connector, XT60 Plug. Applications: nemesis 240 mini, qav180/210, flip fpv frame, danaus, mini shredder 200, emax nighthawk 250, mini h, skylark m4-fpv250, vortex 285, mojo 280, indy250 PLUS, zmr 250, ZMR 250, QAV250, HOVERSHIP MHQ2 270, hovership mhq2, Mini H, emax nighthawk 250, etc.

What you get: tattu lipo battery pack with XT60 Plug & Local after-sales service located in Dublin, CA.

More information about Tattu TA-75C-1300-4S1P


Similar products



Readytosky 220mm FPV Racing Drone Frame for Martian II Carbon Fiber Quadcopter Frame Kit 4mm Arms with Power Distribution Board5030 propellers,Battery Strap


Readytosky - Weight: 1. 2g, dimensions: 20mm*13mm*4. 5mm. It is compact and easy to install. Compitable transmitter: all afhds 2a transmitters, FS-i10, FS-i6S, fs-i6, FS-i8, FS-i6X, fs-i4, FS-i4X. The fs-x6b receiver is a 6 channel two-way receiver designed for multi-rotor aircraft. It's compact, easy to install and boasts a rich easy to use interface.

It supports 6 channel pwm output, standard PPM output and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface. Easy to bind with transmitter: https://www. Youtube. Com/watch?v=5yZG631iXwQ. Support for 32mm board cams as well as HS1177. Support to carry hd camera such as the GoPro 4, runcam 2, or GoPro Session.

Readytosky 220mm FPV Racing Drone Frame for Martian II Carbon Fiber Quadcopter Frame Kit 4mm Arms with Power Distribution Board5030 propellers,Battery Strap - Suit for brushed Quadcopter and other small size quads. Easy lipo access suggested lipo is a 1550mah&2300mah 3 or 4s;Included PDB with XT60 male plug. Special features: full 3k carbon fiber airframe featuring a solid 4mm removable arms Custom aluminum hardware to enable one tool, quick swapping of arms in race pit settings ;Black Oxide steel screws Multiple motor mounting holes to fit a variety of motors M3 and M2 screw mounting patterns.

Multiple motor mounting holes to fit a variety of motors M3 and M2 screw mounting patterns. Easy lipo access suggested lipo is a 1550mah&2300mah 3 or 4s;Included PDB with XT60 male plug. If you need replacement arms, ASIN: B07BVBL885.

More information about Readytosky


Similar products



M3 Flight Controller Anti-Vibration Fixed Screws Mounting Hardware Standoffs Spacer for Naze32 CC3D F3 F4 Flight Controller


LongJinSheng - It is compact and easy to install. Range:about 200m. Specification: item name: 12pcs rubber Flight Controller Standoffs Standoff Hight: 7mm Standoff Base Depth: 3mm Weight: 2. 5g per set package Including 12pcs Rubber M3*7+4. 5 m3 flight controller soft mount12pcs m3 rubber washer o rings receiver compatible with fs-i4, fs-i6, fs-i6x, fs-gt2e, fs-gt2g, FS-i10, fs-i6s, FS-GT2F.

Fs series RC transmitter. It uses the afhds 2a automatic Frequency Hopping Digital System protocol prevent signal interference. The a8s supports 8-channel pwm signal output, a standard PPM signal outputs, 18 channels of I-BUS signal and a voltage detection interface. Three seconds fast response, small size, powerful, easy to carry.

M3 Flight Controller Anti-Vibration Fixed Screws Mounting Hardware Standoffs Spacer for Naze32 CC3D F3 F4 Flight Controller - Fs-a8s is a two-way receiver designed specifically for multi-axis aircraft, rich interface, has a powerful anti-jamming capability, good compatibility. Suit for brushed Quadcopter and other small size quads. Compitable transmitter: all afhds 2a transmitters, FS-i6X, fs-i6, fs-i4, FS-i8, FS-i6S, FS-i10, FS-i4X.

The fs-x6b receiver is a 6 channel two-way receiver designed for multi-rotor aircraft. It's compact, easy to install and boasts a rich easy to use interface. It supports 6 channel pwm output, standard PPM output and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface. Easy to bind with transmitter: https://www.

More information about LongJinSheng


Similar products



DALPROP 16pcs Cyclone T5046C 5046 3 Blades 5.0 x 4.6 CW CCW Propeller for FPV Racing Quadcopter Frame Kit 4sets, mix color


DALPROP Cyclone T5046C - It will make your vehicle more sensitive obedient and better finish it, "a UAV mission. ". Small and lightweight, fs-i6, fs-i10, compatible with FS-I4, fs-i6x, fs-gt2F, fs-gt2e, fs-gt2g, Turnigy Evolution. Afhds 2a protocol, output: PPM/IBUS. Dalprop cyclone t5046c 5046 3 Blades 5. 0 x 4. 6 cw ccw propellert5046c propeller with faster reaction, hk250, 250 and 210 sized fpv racers like : qav250, durability and balanceperfect for 280, easier Cornering Insane Punch-Out Power and Less Noise Made with High Quality Polycarbonate for Maximum Performance, Walkera 250, FPV250, QAV250Specification:Brand name: DalpropItem name: Cyclone T5046CSize: 5046 5x4.

6mounting hole: 5mmcolor: blue, red, fs-gt2e, fs-i10, fs-i6, greencompatible model:200mm to 250mm mini quadcopter dronepackage included:2 pairs x T5046C propeller red2 pairs x T5046C propeller green2 pairs x T5046C propeller blue2 pairs x T5046C propeller purple1 x battery strap 20x200mm random color Receiver compatible with fs-i4, Purple, fs-gt2g, fs-i6x, fs-i6s, FS-GT2F.

DALPROP 16pcs Cyclone T5046C 5046 3 Blades 5.0 x 4.6 CW CCW Propeller for FPV Racing Quadcopter Frame Kit 4sets, mix color - Fs series RC transmitter. It uses the afhds 2a automatic Frequency Hopping Digital System protocol prevent signal interference. The a8s supports 8-channel pwm signal output, a standard PPM signal outputs, 18 channels of I-BUS signal and a voltage detection interface. Three seconds fast response, powerful, small size, easy to carry.

Fs-a8s is a two-way receiver designed specifically for multi-axis aircraft, has a powerful anti-jamming capability, rich interface, good compatibility. Tattu professional lipo Battery; Superior Japan and Korea Lithium Polymer raw materials.

More information about DALPROP Cyclone T5046C


Similar products



Makerfire 2pcs 5.8GHz FPV Antenna Circular Polarized TX RX RHCP RP-SMA for FPV Racing Drone Like QAV250


Makerfire - Mounting hole: 5mm; shape: Cyclone; Size: 5046 5x4. 6. Tattu professional lipo Battery; Superior Japan and Korea Lithium Polymer raw materials. Quickly recharged, long cycle life 150 times minimum, up to 200Wh/kg energy density. Parameter: weight, 155g; dimensionl*w*h, 72*36*29. 4mm; connector, XT60 Plug. Applications: nemesis 240 mini, vortex 285, zmr 250, indy250 plus, mini h, emax nighthawk 250, hovership mhq2, skylark m4-fpv250, mini Shredder 200, danaus, mojo 280, flip fpv frame, zmr 250, emax nighthawk 250, HOVERSHIP MHQ2 270, qav180/210, Mini H, QAV250, etc.

What you get: tattu lipo battery pack with XT60 Plug & Local after-sales service located in Dublin, CA. Full 3k carbon fiber airframe featuring a solid 4mm removable fpv frame arms. Custom aluminum hardware to enable one tool, quick swapping of arms in race pit settings ;Black Oxide steel screws. Weight: 1.

Makerfire 2pcs 5.8GHz FPV Antenna Circular Polarized TX RX RHCP RP-SMA for FPV Racing Drone Like QAV250 - 2g, dimensions: 20mm*13mm*4. 5mm. Gain: 3dbi, frequency range: 5600-5950 MHz. Omnidirectional: 3db horizontal lobe width: 360°, 3dB verticle lobe width: 120°. It will make your vehicle more sensitive obedient and better finish it, "a UAV mission.

More information about Makerfire


Similar products



Floureon 2 Packs 3S 11.1V 1500mAh 35C RC Lipo Battery with XT60 Plug for RC Car, Skylark m4-fpv250, Mini Shredder 200, Qav250, Vortex, Drone and FPV 2.91 x 1.46 x 1.08 Inch


Floureon - Pre-balanced, "indestructible" t5046c 5. 0 x 4. 6 cyclone tri-blade propellers made from super tough glass reinforced polycarbonate. Package included: ●2x Floureon 3S 11. 1v 1500mah 35c rc lipo battery with xt60 plug receiver compatible with fs-i4, fs-gt2e, fs-i6, fs-i6s, fs-i6x, FS-i10, fs-gt2g, FS-GT2F.

Fs series RC transmitter. It uses the afhds 2a automatic Frequency Hopping Digital System protocol prevent signal interference. The a8s supports 8-channel pwm signal output, a standard PPM signal outputs, 18 channels of I-BUS signal and a voltage detection interface. Three seconds fast response, small size, powerful, easy to carry.

Fs-a8s is a two-way receiver designed specifically for multi-axis aircraft, has a powerful anti-jamming capability, rich interface, good compatibility. Range:about 200m. 5. 8 ghz circular polarized Antenna Set for transmitter and receiver. All floureon products sold by SEVESTO are comply with RoHS, CE standard.

Floureon 2 Packs 3S 11.1V 1500mAh 35C RC Lipo Battery with XT60 Plug for RC Car, Skylark m4-fpv250, Mini Shredder 200, Qav250, Vortex, Drone and FPV 2.91 x 1.46 x 1.08 Inch - Application】rc airplane, drone, mini shredder 200, fpv, indy250 plus mojo 280, truck, Skylark m4-fpv250, car, Qav250, boat, vortex and emax nighthawk 250 only if the voltage, dimension and the plug match, helicopter, then it will fit. Only if the voltage, dimension and the plug match, then it will fit.

Specification: ●brand: floureon ●Chemistry: Li-polymer ●Voltage: 11.

More information about Floureon


Similar products



iFlight 2.4G Receiver Antenna with IPEX Interface Compatible with Futaba FrSky Silver-plated Feeder 20pcs


iFlight - Material: cu, Weight: 12g. Item specifics use: vehicles and remote control toys technical parameters: value 2 For Vehicle Type: Helicopters/ Quadcopters/ Multirotors Tool Supplies: Assembly Category Material: Plastic RC Parts & Accessories: Antennas Plastic Type: ABS Model Number: 2. 4g receiver antenna four-wheel Drive Attributes: Assemblage Remote Control Peripherals Devices: 2.

4g receiver antenna Upgrade Parts Accessories: 2. 4g receiver Antenna A. Electrical characteristics: Frequency:2400-2500 MHz Antenna Gain :2. 0 polarization : linear Impedance : 50 Ohm B. Material & mechanical characteristics Cable Type : RG-113 Connector Type: IPEX C. Weight: 1. 2g, dimensions: 20mm*13mm*4. 5mm. Material: silver-plated, Cable length:15cm.

iFlight 2.4G Receiver Antenna with IPEX Interface Compatible with Futaba FrSky Silver-plated Feeder 20pcs - . Compitable transmitter: all afhds 2a transmitters, FS-i10, fs-i4, FS-i6S, FS-i8, fs-i6, FS-i6X, FS-i4X. The fs-x6b receiver is a 6 channel two-way receiver designed for multi-rotor aircraft. It's compact, easy to install and boasts a rich easy to use interface. It supports 6 channel pwm output, standard PPM output and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface.

More information about iFlight


Similar products