Top 10 Gx24q-3 to E26/E27 Light Socket Adapter – Light Sockets

As an Amazon Associate I earn from qualifying purchases.

1. Bonlux

#ad

Bonlux 6-pack Gx24q to E26/E27 Socket Adapter, Gx24 Short 4 Pin to Medium Edison Lamp Base Converter, Rewire/Remove/Bypass the Ballast is Required

#ad
Bonlux #ad - Even you are replacing with e26/e27 cfl, please dismantle the ballast before install the LED light, the CFL E26/e27 Lamp will be flickering or not even turn on! Attention buyers: rewiring & removing/bypassing the ballast at the light fixture is required for these adapters to function properly.

If there is a ballast connected at your fixture, you need to remove the ballast! Otherwise, otherwise the ballast will make resonance high voltage which can destroy the light. Do not operate the led bulb with a ballast in the fixture. Please consult an electrician if you are unsure. Save you a lot of troubles and money to replace your original Halogen CFL lighting fixtures. The base depth of this product is 15mm/059 inches.

Easily transfer your gx24 fixture to fit any of the E26/E27 standard medium base light bulbs. Doing so will likely cause the bulb flickering and EVEN SMOKING!! This lamp base converter doesn't change any voltage or current. Note: it is 100% that PL-C downlight fixture has ballast inside. It has the short version 4-pins and is suitable and compatible with 4 pin g24q-1, G24Q-3, GX24Q-1, G24Q-2, GX24Q-2, GX24Q-3 Please confirm what base you need before you buy.
BrandBonlux #ad
ManufacturerLusta LED Co., Ltd #ad
Height3.14 Inches
Length2.04 Inches
Weight5 ounces
Width3.14 Inches

2. E-Simpo

#ad

Need Bypass BallastGX24Q-3 to E26/E27 CFL Bulb Socket Adapter 6pcs E-Simpo 4-Pin GX24Q G24Q to Standard Medium Bulb Holder Base Converter

#ad
E-Simpo #ad - It is 100% that pl-c downlight fixture has ballast inside. 4pin gx24q or g24q to e26/e27 light socket adapter. Please make sure the lamp base type before you buy, DON'T Mix with other 2P 4P socket. Home or commercial use, Suitable for less than 100W.

Need rewiring!!! not for diy, please install it only with qualified electrician!!! bypass/ remove the ballast, and connect 2 red to black, two red and two blue output side. Short version 4-pins: q series has a shorter tip than d series, g24q-2. G24q-3, suitable for g24q-1, gx24q-2, gx24q-1, gx24q-3 socket;works for 4-pin cfl with g24q-1 base:10w 13w quad tube; gx24q-1 base:10w 13w triple Tube;G24q-2 Base:18w Quad Tube;GX24q-2 Base:18w Triple Tube;G24q-3 Base:26w 32w Quad Tube;GX24q-3 Base:26w 32w Triple Tube;.

To bypass this ballast, the ballast has a black and white wire on the input side, cut all the Input and output wires, 2 Blue to White wire. With base depth 15. 5mm/06 inches. 6pcs. No ballast is required. Dismantle ballast before install the led light, otherwise the ballast will make resonance high voltage which destroy the light, smell, hot, reviews like burnt, flicking are all results that not bypass the ballast correctly. Material: anti-burning pbt, copper contact.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
ModelGX24Q-E26

3. E-Simpo

#ad

Must Bypass Ballast to Avoid Flick Smoke Burn 6pcs E-Simpo 4Pin Conductive Gx24q to E26/E27 Lamp Base Adapter Short G24q to Medium Edison Light Socket Converter Replace CFL PL GX24Q Holder

#ad
E-Simpo #ad - But no led driver can be compatible with all ballast. Ballast is there consuming power, cause high temperature which will damage LED Bulb, E26/E27 bulbs are self-ballast. There are led bulbs with driver compatible with the ballast, so the professional doing is bypass it.

Do not operate a led bulb with a ballast in the fixture, doing so will likely damage the bulb. All pin-based cfl, so 600-1500v will be too high, but all screw-in e26 e27 are lamp-ballast integrated. Because led lamp are built with leds and driver which is transforming the 100-240V AC to DC for LEDs. So the led driver input should be 100V-240V or 85-265V, and easily destroy the led lamp. Ballast is a must to start a high voltage600v-1500v 1ms to light up the cfl, like gx24q G24 GX23 G23 are lamp-ballast separated, but it is dangerous for LED Lamp.

All pin-based cfl is ballast-lamp separated, which you may find work without bypass ballast. To bypass this ballast, cut all the input and output wires, not for 2p;not for diy!!! need rewiring/bypASS/ REMOVE the ballast, the ballast has a black and white wire on the input side, and connect 2 Red to Black, 2 Blue to White wire. Consult an electrician if you are unsure. This is 4p short 15. 5mm gx24q base, two red and two blue output side.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
Part NumberGX24Q-E26
ModelGX24Q to E26/E27 Adapter

4. E-Simpo

#ad

2pcs E-Simpo 4Pin Gx24q to E26/E27 Light Socket Adapter Lamp Base Converter. NOT PLUG AND PLAY, Need Rewire to Bypass Ballast. 2-Pack

#ad
E-Simpo #ad - There are some led driver who can be compatible with the ballast, the ballast is still working in front fixture; even we change to E26/E27 CFL, no LED Driver can be compatible with all the ballast. Physically change the socket contact, hot or smell, which will cause the led bulb flickering, twist into existing GX24Q socket and transform the fixture to fit any standard E26 E27 medium size bulb.

Pbt housing, copper contact. Suitable for all voltage: 100-240v, works for 4-pin cfl with g24q-1 base:10w 13w quad tube; gx24q-1 base:10w 13w triple tube;G24q-2 Base:18w Quad Tube;GX24q-2 Base:18w Triple Tube;G24q-3 Base:26w 32w Quad Tube;GX24q-3 Base:26w 32w Triple Tube.

With base depth is 15. 5mm/06 inches. Short version 4pins, G24Q-2. G24q-3, suitable for g24q-1, gx24q-1, GX24q-3 socket;. So the best thing is bypass or remove once we want to change CFL to LED Lamp. When we remove pin-based cfl, we only removed the lamp, there will be 2 ballasts, the light will not work. Consult an electrician if you are unsure. 4p conductive, e-simpo's new generation.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
Weight66 Grams

5. E-Simpo

#ad

10pcs E-Simpo 4Pin Gx24q CFL to E26/E27 Lamp Base Socket Adapter Converter. Need Rewire to Bypass Ballast. 10-Pack

#ad
E-Simpo #ad - So the best thing is bypass or remove once we want to change CFL to LED Lamp. This is 4p, otherwise, not for 2p;need bypass or remove the ballast, it doesn't light on. Ballast is a must to start a high voltage600v-1500v 1ms to light up the cfl, like gx24q g24 gx23 g23 are lamp-ballast separated, but it is dangerous for LED Lamp.

The ballast in your fixture must be removed or bypassed for these adapters to function properly. There are some led driver who can be compatible with the ballast, we only removed the lamp, the ballast is still working in front fixture; even we change to E26/E27 CFL, no LED Driver can be compatible with all the ballast. Do not operate a led bulb with a ballast in the fixture, doing so will likely damage the bulb. All pin-based cfl, but all screw-in e26 e27 are lamp-ballast integrated.

So the led driver input should be 100v-240v or 85-265V, so 600-1500V will be too high, and easily destroy the led lamp. G24q series female socket fixture to e26 male Bulb Base Adapter - Q series has a shorter tip than D series and is more common in the US. Because led lamp are built with leds and driver which is transforming the 100-240V AC to DC for LEDs. Consult an electrician if you are unsure. When we remove pin-based CFL, there will be 2 ballasts, the light will not work.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
Height2.3 Inches
Length1.5 Inches
Weight0.05 Pounds
Width1.5 Inches
Part NumberGX24Q-E26

6. E-Simpo

#ad

4pcs E-Simpo 4-Pin GX24Q to E26/E27 Light Socket Adapter Need Bypass Ballast CFL G24Q 4P Lamp Base to Standard LED E26 e27 Lamp Base Holder Converter PBT Housing Rohs

#ad
E-Simpo #ad - Do not operate a led bulb with a ballast in the fixture, doing so will likely damage the bulb. All pin-based cfl, so 600-1500v will be too high, but all screw-in e26 e27 are lamp-ballast integrated. Works for 4-pin cfl with g24q-1 base:10w 13w quad tube; gx24q-1 base:10w 13w triple tube;g24q-2 base:18w quad tube;gx24q-2 Base:18w Triple Tube;G24q-3 Base:26w 32w Quad Tube;GX24q-3 Base:26w 32w Triple Tube.

So the led driver input should be 100V-240V or 85-265V, and easily destroy the led lamp. Ballast is a must to start a high voltage600v-1500v 1ms to light up the cfl, like g24d gx24d GX24Q GX23 G23 are lamp-ballast separated, but it is dangerous for LED Lamp. Because led lamp are built with leds and driver which is transforming the 100-240V AC to DC for LEDs.

Consult an electrician if you are unsure. 4pcs. 4pin gx24q, not for 2p; need bypass or remove the ballast, all phenom like smell smoke flicker burnt are caused by ballast which is not required for LED Lamps. G24q series female socket fixture to e26 male Bulb Base Adapter - Q series has a shorter tip than D series and is more common in the US. The ballast in your fixture must be removed or bypassed for these adapters to function properly.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
Part NumberGX24Q-E26
ModelGX24Q-E26

7. E-Simpo

#ad

Gx24q to E26 Adapter,Lamp Holder Converter, 15-Pack 4P Gx24q to E26 Lamp Base Converter,15.5mm G24Q to E26/e27, Rohs,Need Bypass Ballast.

#ad
E-Simpo #ad - All pin-based cfl, but it is dangerous for led lamp. Because led lamp are built with leds and driver which is transforming the 100-240v ac to dc for leds. Consult an electrician if you are unsure. Do not operate a led bulb with a ballast in the fixture, doing so will likely damage the bulb.

So the best thing is bypass or remove once we want to change CFL to LED Lamp. This is 4p, otherwise, not for 2p;need bypass or remove the ballast, it doesn't light on. The ballast in your fixture must be removed or bypassed for these adapters to function properly. G24q series female socket fixture to e26 male Bulb Base Adapter - Q series has a shorter tip than D series and is more common in the US. So the led driver input should be 100v-240V or 85-265V, but all screw-in E26 E27 are lamp-ballast integrated.

When we remove pin-based CFL, the light will not work. Ballast is a must to start a high voltage600v-1500v 1ms to light up the cfl, so 600-1500V will be too high, like GX24Q G24d Gx24d GX23 G23 are lamp-ballast separated, and easily destroy the led lamp. There are some led driver who can be compatible with the ballast, the ballast is still working in front fixture; even we change to E26/E27 CFL, there will be 2 ballasts, we only removed the lamp, no LED Driver can be compatible with all the ballast.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
Height1.5 Inches
Length1.5 Inches
Weight0.88 Pounds
Width2.31 Inches
Part NumberG24-E26
ModelGX24Q to E26 Light Socket Adapter
Warranty1 year for the lamp holder, but don't blame the converter if
1. You don't bypass the ballast when your e26 lamp is not compatible with the ballast;
2. The socket is not gx24q or g24q, whose 4 holes has contact and 2 holes at one side are mutually connected or all 4 holes has wires out, one side, 2 holes' wires go to l, the other side goes to n.

8. TWDRTDD

#ad

E27 to G24 Adapter,TWDRTDD 3 PACK E26/E27 Edison Screw to 4 Pin G24 Base Bulb Socket Adapter Converter

#ad
TWDRTDD #ad - Convert your existing e26 base fixture US standard light bulb socket into a 4 pin PL Style G24 Bulb. The e26/e27 to g24 adapter fit for g24/g24x/g24q/G24xq 4 Pin bulbs boths fit for 2 pin. The maximum wattage for this adapter is 200W. 100% brand new and high quality, Easy to use, just twist into existing socket. Standard e26 to g24q base adapter converter for LED/ halogen / CFL light bulb lamp. This e26 to g24q adapter works with bulbs operating at 110-250 volts.
BrandTWDRTDD #ad
ManufacturerSM #ad

9. OmeiLighting

#ad

2-Pack 4Pin Light Socket Adapter, Gx24q to E26/E27 Lamp Base Converter. Need Rewire to Bypass Ballast

#ad
OmeiLighting #ad - Not for diy!!! need rewiring! removing or bypassing the ballast inside the light fixture is required. Physically change the socket contact, burnt, hot or smell, twist into existing gx24q socket and transform the fixture to fit any standard E26 E27 medium size bulb.

Consult an electrician if you are unsure. So the best thing is bypass or remove once we want to change CFL to LED Lamp. When we remove pin-based CFL, the light will not work. But mostly gx24q cfls are with an electronic ballast inside, which will cause the LED bulb flickering, and damage the electrical parts inside the bulb. Doing so will likely damage the bulb. There are some led driver who can be compatible with the ballast, we only removed the lamp, there will be 2 ballasts, the ballast is still working in front fixture; even we change to E26/E27 CFL, no LED Driver can be compatible with all the ballast.

Short version 4pins, G24Q-2. G24q-3, gx24q-3 socket;. 2pcs/lot, gx24q-2, gx24q-1, suitable for g24q-1, sample pack. Pbt housing, works for 4-pin cfl with g24q-1 base:10w 13w quad tube; gx24q-1 base:10w 13w triple tube;g24q-2 base:18w Quad Tube;GX24q-2 Base:18w Triple Tube;G24q-3 Base:26w 32w Quad Tube;GX24q-3 Base:26w 32w Triple Tube. Do not operate the led bulb with ballast in the fiXTURE.
BrandOmeiLighting #ad
ManufacturerOmeiLighting #ad

10. E-Simpo

#ad

15.5mm 4pin,Need Bypass The Inside Ballast!, 60-Pack GX24q to E26 Lamp Base Converter,GX24q-3 Adapter,G24 to E26 Adapter

#ad
E-Simpo #ad - G24q series female socket fixture to e26 male Bulb Base Adapter - Q series has a shorter tip than D series and is more common in the US. The ballast in your fixture must be removed or bypassed for these adapters to function properly. Ballast is a must to start a high voltage600V-1500V 1ms to light up the CFL, but it is dangerous for LED Lamp.

This is 4p, not for 2p;need bypass or remove the ballast, otherwise, it doesn't light on. So the best thing is bypass or remove once we want to change CFL to LED Lamp. All pin-based cfl, like gx24q g24 gx23 g23 are lamp-ballast separated, so 600-1500v will be too high, but all screw-in e26 e27 are lamp-ballast integrated. Suit for g24q-1, gx24q-1, works for 4-pin cfl with g24q-1 base:10w 13w quad tube; gx24q-1 base:10w 13w triple tube;g24q-2 base:18w quad tube;gx24q-2 base:18w triple tube;g24q-3 base:26w 32w quad tube;gx24q-3 base:26w 32w Triple Tube; If your socket is 2P, GX24q-3 socket, GX24q-2, G24Q-2.

G24q-3, buy: https://www. Amazon. Com/dp/b017t1ujee Physically change the contact. When we remove pin-based CFL, we only removed the lamp, the light will not work. There are some led driver who can be compatible with the ballast, the ballast is still working in front fixture; even we change to E26/E27 CFL, there will be 2 ballasts, no LED Driver can be compatible with all the ballast. Consult an electrician if you are unsure.
BrandE-Simpo #ad
ManufacturerE-Simpo #ad
Height2.3 Inches
Length1.5 Inches
Weight0.05 Pounds
Width1.5 Inches
Part NumberGX24Q-E26